Manual Diaphragm Valve
MOD Manually Operated Diaphragm Valve is ideal for Cyanoacrylates and other low to medium viscosity fluids, for use in an operator applied situation. Holding the lever down will apply the material, while a simple lift of the finger from the lever (shown left) will cause the diaphragm to close. The MOD is hand actuated; no need for an expensive valve controller.
|
Diaphragm Valve Features:
|
Simple Maintenance and Operation
- Plumb the material line.
- Pressurize the fluid delivery system and regulate the material to be dispensed with low pressure.
- Cycle the valve open by pressing the lever on the valve.
- Fluid should will begin to dispense from the tip of the valve.
- Adjust the pressure on the material inlet and connect the proper dispense tip to the luer lock fitting on the end of the valve.
- Turn the valve upright with the tip pointing in the air.
- Hold tip over a purge cup or cover the tip with a cloth.
- Trigger the valve to dispense until bubbles clear the system.
- Once purged, dispensing can begin.
- Material inlet pressure and needle size will effect flow rate of material.
|
MOD Manually Operated Diaphragm Valve Specifications
Weight: 4.8 oz Viscosity Range: 1 cps - 20,000 cps Maximum Fluid Pressure: 60 PSI Wetted Parts: PTFE, Delrin® Dimensions: 159 mm x 44.45 mm Diameter: (6.258 in x 1.75 in Diameter) |
Part # Manual Diaphragm Valves and Kits
7020000 MOD Handheld Valve - manual lever 7020000SP Kit for MOD Handheld - manual lever |
7020000 = Manual Diaphragm Valve ONLY
$
500.00
VALVE ONLY
The 7020000 - Manual Diaphragm Valve is intended to be used with any pressurized reservoir. NO VALVE CONTROLLER REQUIRED.
Availability: From 2 - 4 week build time. Need multiple units? Contact IDS directly for a quote. Note: Know your material! Always confirm compatibility.
The 7020000 - Manual Diaphragm Valve is intended to be used with any pressurized reservoir. NO VALVE CONTROLLER REQUIRED.
Availability: From 2 - 4 week build time. Need multiple units? Contact IDS directly for a quote. Note: Know your material! Always confirm compatibility.
7020000-2LPKG = 2 Liter Manual Diaphragm Dispense System
$
1,475.00
FULL SYSTEM PACKAGE
The 7020000-2LPKG includes the 7020000 manual diaphragm valve, material line, the 7011010-2L - 2 liter open top reservoir, and a desktop stand to hold the valve when not in use. Requires clean compressed air up to 100psi. This system is intended for manual user control only, for dispensing low to medium viscosity flow-able material. Flux, Cyanoacrylates, Paints and more.
REQUIRES A LINER - DO NOT DIRECT POUR. Most customers will use the bottle that the material comes in, set it directly inside, drop the feed tube in, and then pressurize.
Availability: From 2 - 4 week build time. Need multiple units? Contact IDS directly for a quote. Note: Know your material! Always confirm compatibility.
The 7020000-2LPKG includes the 7020000 manual diaphragm valve, material line, the 7011010-2L - 2 liter open top reservoir, and a desktop stand to hold the valve when not in use. Requires clean compressed air up to 100psi. This system is intended for manual user control only, for dispensing low to medium viscosity flow-able material. Flux, Cyanoacrylates, Paints and more.
REQUIRES A LINER - DO NOT DIRECT POUR. Most customers will use the bottle that the material comes in, set it directly inside, drop the feed tube in, and then pressurize.
Availability: From 2 - 4 week build time. Need multiple units? Contact IDS directly for a quote. Note: Know your material! Always confirm compatibility.
7020000-5LPKG = 5 Liter Manual Diaphragm Dispense Station
$
1,799.00
FULL SYSTEM PACKAGE
The 7020000-5LPKG includes the 7020000 manual diaphragm valve, material line, the 7011010-5L - 5 liter open top reservoir, and a desktop stand to hold the valve when not in use. Requires clean compressed air up to 100psi. This system is intended for manual user control only, for dispensing low viscosity flow-able material. Flux, Cyanoacrylates, Paints and more.
REQUIRES A LINER - DO NOT DIRECT POUR. Most customers will use the bottle that the material comes in, set it directly inside, drop the feed tube in, and then pressurize.
Availability: From 2 - 4 week build time. Need multiple units? Contact IDS directly for a quote. Note: Know your material! Always confirm compatibility.
The 7020000-5LPKG includes the 7020000 manual diaphragm valve, material line, the 7011010-5L - 5 liter open top reservoir, and a desktop stand to hold the valve when not in use. Requires clean compressed air up to 100psi. This system is intended for manual user control only, for dispensing low viscosity flow-able material. Flux, Cyanoacrylates, Paints and more.
REQUIRES A LINER - DO NOT DIRECT POUR. Most customers will use the bottle that the material comes in, set it directly inside, drop the feed tube in, and then pressurize.
Availability: From 2 - 4 week build time. Need multiple units? Contact IDS directly for a quote. Note: Know your material! Always confirm compatibility.
