Front Closing Valve (Standard High Pressure)
Front Closing Valves operate by a combination of pneumatic and mechanical functions - by a regulated flow of air pressure and a spring assist. These combine to help move and manage material that fills the interior chamber. The pressure forces the valve to open, which in turn lifts the needle, permitting fluid to flow. The length of the needle stroke is determined by the stroke adjustment knob located at the top of the valve. Using a timer, the air solenoid will then close and force the needle down. In addition to the air pressure, there is a spring assist to help close the opening, giving you a clean, sharp cutoff, eliminating messy dripping and stringing. This is an excellent all purpose, single material valve, used in a variety of applications, including beads, gaskets, shots large and small (using the micro version) potting and bonding. This valve is often referred to as a front closing valve, needle valve, high pressure valve, or silicone valve, and is perfect for grease dispensing, lubricant dispensing valve, silicone dispensing. As always, be sure to check for material compatibility. If material is gritty, request a quote for the carbide steel version.
|
5101292 Front Closing Valve Features
|
5101292 Front Closing Valve Specifications
Dimensions: 152 mm x 19 mm x 19 mm (6.00 in x 0.75 in x 0.75 in) Weight: 6 oz. Viscosity Range: 1 cps - Paste Operating Air Pressure: 30-100 PSI Maximum Fluid Pressure: 3500 PSI Wetted Parts: Stainless Steel, Teflon®, Kalrez® |
5101292 = Front Closing Valve ONLY
$
795.00
VALVE ONLY
The 5101292 = Front Closing Valve is intended to be used with any pressurized reservoir. Requires a valve controller that can provide air pressure to open and close. These valves are steel and are not suggested for use with CA (Cyanoacrylate) material.
Availability: From 2 - 4 week build time. Need multiple units? Contact IDS directly for a quote. Note: Know your material! Always confirm compatibility.
The 5101292 = Front Closing Valve is intended to be used with any pressurized reservoir. Requires a valve controller that can provide air pressure to open and close. These valves are steel and are not suggested for use with CA (Cyanoacrylate) material.
Availability: From 2 - 4 week build time. Need multiple units? Contact IDS directly for a quote. Note: Know your material! Always confirm compatibility.
5101292-2LPKG = 2 Liter Front Closing Valve Dispense Station
$
2,995.00
FULL SYSTEM PACKAGE
The 5101292-2LPKG includes the 5101292 Front Closing Valve the 7011010-2L - 2 liter open top reservoir, the 5900011VC valve controller and a desktop stand to hold the valve over the work area. Requires clean compressed air up to 100psi.
This system is intended for timed metered shots or manual user control, used in automation or at the desktop level for potting and encapsulation for electronics and medical device, Filling molds, timed dispensed shots filling vials or other receptacles, epoxy dispensing, flux, dam and fill, Paints and more. These valves are steel and are not suggested for use with CA (Cyanoacrylate) material.
REQUIRES A LINER - DO NOT DIRECT POUR. Most customers will use the bottle that the material comes in, set it directly inside, drop the feed tube in, and then pressurize.
Availability: From 2 - 4 week build time. Need multiple units? Contact IDS directly for a quote. Note: Know your material! Always confirm compatibility.
The 5101292-2LPKG includes the 5101292 Front Closing Valve the 7011010-2L - 2 liter open top reservoir, the 5900011VC valve controller and a desktop stand to hold the valve over the work area. Requires clean compressed air up to 100psi.
This system is intended for timed metered shots or manual user control, used in automation or at the desktop level for potting and encapsulation for electronics and medical device, Filling molds, timed dispensed shots filling vials or other receptacles, epoxy dispensing, flux, dam and fill, Paints and more. These valves are steel and are not suggested for use with CA (Cyanoacrylate) material.
REQUIRES A LINER - DO NOT DIRECT POUR. Most customers will use the bottle that the material comes in, set it directly inside, drop the feed tube in, and then pressurize.
Availability: From 2 - 4 week build time. Need multiple units? Contact IDS directly for a quote. Note: Know your material! Always confirm compatibility.
5101292-5LPKG = 5 Liter Front Closing Valve Dispense Station
$
3,495.00
FULL SYSTEM PACKAGE
The 5101292-5LPKG includes the 5101292 Front Closing Valve the 7011010-5L - 5 liter open top reservoir, the 5900011VC valve controller and a desktop stand to hold the valve over the work area. Requires clean compressed air up to 100psi.
This system is intended for timed metered shots or manual user control, used in automation or at the desktop level for potting and encapsulation for electronics and medical device, Filling molds, timed dispensed shots filling vials or other receptacles, epoxy dispensing, flux, dam and fill, Paints and more. These valves are steel and are not suggested for use with CA (Cyanoacrylate) material.
REQUIRES A LINER - DO NOT DIRECT POUR. Most customers will use the bottle that the material comes in, set it directly inside, drop the feed tube in, and then pressurize.
Availability: From 2 - 4 week build time. Need multiple units? Contact IDS directly for a quote. Note: Know your material! Always confirm compatibility.
The 5101292-5LPKG includes the 5101292 Front Closing Valve the 7011010-5L - 5 liter open top reservoir, the 5900011VC valve controller and a desktop stand to hold the valve over the work area. Requires clean compressed air up to 100psi.
This system is intended for timed metered shots or manual user control, used in automation or at the desktop level for potting and encapsulation for electronics and medical device, Filling molds, timed dispensed shots filling vials or other receptacles, epoxy dispensing, flux, dam and fill, Paints and more. These valves are steel and are not suggested for use with CA (Cyanoacrylate) material.
REQUIRES A LINER - DO NOT DIRECT POUR. Most customers will use the bottle that the material comes in, set it directly inside, drop the feed tube in, and then pressurize.
Availability: From 2 - 4 week build time. Need multiple units? Contact IDS directly for a quote. Note: Know your material! Always confirm compatibility.
|
Part #
5101292 5101292-SP 7080003 7080006 |
Description
Front Closing, high pressure valve. 5101292 Front Closing Valve Spare Parts Kit Electric Finger Switch, Mount to Front Closing Valves Valve Stand |
