Syringe Heating System

This system is made up of two parts; The Heat Zone Controller (Readout in degrees C) and Heated Pistol Grip. The Heat Zone Controller offers 2 different contact point control options, one at the needle tip and one for the barrel in the Heated Pistol Grip.
It is intended to work with the electric triggers on our Analog Timed Air Dispenser or Digital Dual Gauge Dispenser. If you already have one of these dispensers, then you should only purchase the Syringe Heating System Alone. Otherwise, you need to add the dispenser of your choice in the full system packages.
Polyurethane is a polymer alternative to rubber, it is flexible and works in a range or temp settings and creates strong bonds. IDS does not offer any formulations, and it is up to the customer to be aware of all the safety requirements. Always use protective clothing, gloves, and eye or face protection when dispensing, and always make sure the work area is properly ventilated and secure.
You should use our all metal tips, usually in the 1" length and 15 gauge or smaller to help properly fit the heating element and protrude beyond the tip to a good work distance. Tips with steel shafts and plastic hubs use epoxy to hold the cannula in the hub. This epoxy could heat and break down, especially under pressure so it is best to use the all metal tips that have the shaft crimped into the hub. At lower heats some customers will continue to use the disposable plastic hubs. It is up to the customer to decide.
NEVER TOUCH THE HEAT CYLINDER IN THE GUN OR THE TIP WHILE HOT, AND NEVER RUN AN EMPTY SYRINGE. We do not suggest heating above 120 C. The customer assumes all risk when deciding how to use this system. The all metal tip will also remain hot after removing a syringe from the gun. IDS Syringes should not be heated empty. Heating an empty syringe too hot for too long could melt the syringe. Spare guns are available as special order if they are needed.

Includes the 5101284DG IntelliSpense™ Dual Gauge Digital Dispenser, complete with starter accessory dispensing kit: 30cc/ml syringes, adapter head, foot pedal trigger, and small selection of needles, tips and lab stand. This is our most popular dispenser, both for ease of use and the combination of digital timer and analog "dial" readouts on the front panel.
Includes 5101SHSIntelliSpense™ Syringe heating system with Heat Zone controllers for both the Barrel and the Tip, And heated pistol grip for 30cc/ml syringes. Do not exceed 120C.
Air Input: 1/4" Tube or 1/4" Quick Connect Hose Barb (Male Provided With Dispenser)
SHIPPING COST INCLUDED IN PRICE - UPS Ground anywhere in the Continental US.
Availability: Ranges from in stock to 4 weeks.
Need multiple units? Contact IDS directly for a quote.

Includes the IntelliSpense™ Analog Timed Air Dispenser, complete with starter accessory dispensing kit: 30cc/ml syringes, adapter head, foot pedal trigger, and selection of needles, tips and lab stand. FINGER SWITCH NOT INCLUDED.
Includes 5101SHSIntelliSpense™ Syringe heating system with Heat Zone controllers for both the Barrel and the Tip, And heated pistol grip for 30cc/ml syringes. Do not exceed 120C.
Air Input: 1/4" Tube or 1/4" Quick Connect Hose Barb (Male Provided With Dispenser)
SHIPPING COST INCLUDED IN PRICE - UPS Ground anywhere in the Continental US.
Availability: Ranges from in stock to 4 weeks.
Need multiple units? Contact IDS directly for a quote.

Intended for use with the 5101284 IntelliSpense™ Analog Timed Air Dispenser, or the 5101284DG IntelliSpense™ Digital Dual Guage Syringe Dispenser.
Includes the5101SHS IntelliSpense™ Syringe heating system with Heat Zone controllers for both the Barrel and the Tip, And heated pistol grip for 30cc/ml syringes. Do not exceed 120C.
Air Input: 1/4" Tube or 1/4" Quick Connect Hose Barb (Male Provided With Dispenser)
SHIPPING COST INCLUDED IN PRICE - UPS Ground anywhere in the Continental US.
Availability: Ranges from in stock to 4 weeks.
Need multiple units? Contact IDS directly for a quote.

REPLACEMENT GUN ONLY - NOT FULL SYSTEM
Intended as replacement, for use with the 5101SHS IntelliSpense™ Syringe heating system Heat Zone controllers. The heated pistol grip is intended for 30cc/ml syringes. Do not exceed 120C.
Includes pistol grip, all internal wiring for the pistol grip trigger and thermo couples, and the 8880365 = 30/55 ML Syringe Adapter for 30cc Syringes
Availability: 4 weeks build time.

REPLACEMENT RETAING CLIP ONLY - NOT FULL SYSTEM
Intended as replacement, for use with the 5101SHS IntelliSpense™ Syringe heating system Heat Zone controllers. The heated pistol grip is intended for 30cc/ml syringes. Do not exceed 120C.
Availability: 4 weeks build time.